Plumber's Essentials: What You Need for Bathtub Installation
Plumber's Essentials: What You Need for Bathtub Installation
Blog Article
Listed here in the next paragraph yow will discover a good deal of sensible help and advice related to Installing A Bathtub.
Installing a bath tub isn't specifically rocket science, however it does need solid plumbing, carpentry, as well as occasionally, tiling abilities. Changing an old tub with a new one is likewise a reasonably challenging task. If the old tub is easily obtainable, the project can move rapidly; if you have to open up a wall surface to get rid of the old bathtub as well as position the new bathtub, the job is much harder. In either case, the job is within a home handyman's skills, although you will certainly require a helper to vacate the old bathtub and set in the new one. Make certain you have actually qualified yourself for the work and fit attempting it. Rather than hiring a professional to take over a halfway-completed task, it is better to consider employing one prior to you begin. Possibilities are you might need a specialist plumber to make tube links.
This short article will certainly aid you install a brand-new bathtub in your bathroom if you have actually currently gotten a brand-new tub and don't require to alter the plan of your previous supply of water pipes.
Your tools as well as product checklist ought to consist of the following:
Preparing for the Installment
Firstly, the sustaining frame supplied with the bath must be fitted (if needed) according to the manufacturer's guidelines. Next, fit the taps or mixer to the bath tub. When fitting the tap block, it is essential to make certain that if the faucet comes with a plastic washing machine, it is fitted in between the bathroom and also the faucets. On a plastic bathroom, it is likewise practical to fit a supporting plate under the taps system to prevent stress on the bath tub.
Fit the versatile tap adapters to the bottom of the two taps utilizing 2 nuts as well as olives (sometimes supplied with the tub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink electrical outlet hole, and then pass the electrical outlet through the hole in the bath. Utilize the nut provided by the supplier to fit the plug-hole. Take a look at the plug-hole outlet for an inlet on the side for the overflow pipe.
Next off, fit completion of the flexible overflow pipe to the overflow electrical outlet. After that, screw the pipeline to the overflow face which should be fitted inside the bathroom. See to it you use every one of the provided washers.
Attach the trap to the bottom of the waste outlet on the bath tub by winding the thread of the waste electrical outlet with silicone mastic or PTFE tape, as well as screw on the catch to the electrical outlet. Attach all-time low of the overflow tube in a comparable manner.The bathroom ought to currently prepare to be fitted in its last setting.
Removing Old Touches
If you require to change old faucets with new ones as a part of your setup, then the first thing you ought to do is detach the water system. After doing so, activate the faucets to drain any water continuing to be in the system. The process of getting rid of the existing taps can be fairly troublesome as a result of the limited gain access to that is usually the case.
Use a basin wrench (crowsfoot spanner) or a faucet device to reverse the nut that links the supply pipes to the faucets. Have a fabric ready for the staying water that will certainly come from the pipes. As soon as the supply pipes have been removed, use the exact same tool to loosen up the nut that holds the taps onto the bath/basin. You will require to stop the solitary faucets from turning throughout this procedure. As soon as the faucets have actually been gotten rid of, the holes in the bath/basin will need to be cleaned of any type of old securing substance.
Prior to carrying on to fit the new faucets, compare the pipeline connections on the old faucets to the brand-new faucets. If the old taps are longer than the new taps, then a shank adapter is required for the new faucets to fit.
Mounting the Bath tub
Using the two wooden boards under its feet, put the tub in the called for position. The wood boards are handy in equally spreading out the weight of the bath tub over the location of the boards rather than concentrating all the weight onto four small points.
The next goal is to make sure that the tub is leveled all round. This can be achieved by examining the level and readjusting the feet on the bathtub till the level checks out degree.
To set up faucets, fit all-time low of the furthest adaptable faucet port to the suitable supply pipe by making a compression sign up with; after that do the exact same for the various other tap.
Switch on the water and also inspect all joints and brand-new pipework for leaks and also tighten them if necessary. Fill up the bathtub as well as additionally check the overflow outlet and the typical electrical outlet for leaks.
Ultimately, take care of the bath paneling as explained in the producer's user's manual. Tiling and securing around the tub must wait up until the tub has actually been made use of at least once as this will settle it into its last position.
Suitable New Touches
If the tails of the new taps are plastic, then you will need a plastic adapter to stop damages to the string. One end of the adapter fits on the plastic tail of the faucet and also the other end provides a connection to the existing supply pipes.
If you need to fit a monobloc, after that you will certainly require minimizing couplers, which links the 10mm pipeline of the monobloc to the common 15mm supply pipeline.
Next, place the tap in the installing opening in the bath/basin guaranteeing that the washing machines remain in place in between the faucet and also the sink. Secure the tap in position with the producer supplied backnut. As soon as the tap is firmly in position, the supply pipelines can be attached to the tails of the faucets. The faucets can either be connected by utilizing corrugated copper piping or with typical tap ports. The former kind should be linked to the tap finishes first, tightening up just by hand. The supply pipes can later on be connected to the various other end. Tighten both ends with a spanner after both ends have actually been connected.
Tiling Around the Bath tub
In the location where the bathroom fulfills the ceramic tile, it is necessary to secure the accompanies a silicone rubber caulking. This is important as the fitting can relocate sufficient to split a stiff seal, triggering the water to penetrate the wall in between the bath and also the tiling, leading to difficulties with dampness as well as possible leaks to the ceiling below.
You can select from a selection of coloured sealers to blend in your components as well as fittings. They are marketed in tubes and also cartridges, as well as can sealing voids approximately a width of 3mm (1/8 inch). If you have a larger void to fill, you can fill it with spins of soaked newspaper or soft rope. Bear in mind to always fill the bathtub with water before sealing, to permit the motion experienced when the tub is in use. The sealant can break relatively early if you do not take into consideration this movement prior to sealing.
Additionally, ceramic coving or quadrant floor tiles can be utilized to edge the bath or shower tray. Plastic strips of coving, which are easy to use as well as cut to dimension, are also quickly available on the marketplace. It is a good idea to fit the floor tiles using water-resistant or water-proof glue as well as cement.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
As an avid person who reads on How to Install a Bathtub, I think sharing that piece of content was really useful. In case you appreciated our blog entry please be sure to pass it around. I truly appreciate reading our article about How to Install a Bathtub: Install an Acrylic Tub and Tub Surround.
Immediate action for plumbing crises. Report this page